Mounting Amps Upside-Down...Any Harm?
#11
I mounted my amps in the spare tire well (JL 300/4 and 500/1). They mount to a board that is actually bolted to the rim of my spare tire. I can unbolt and raise the amp board to pull out the spare tire if need be.
By using the board on top of the spare, the amps are mounted right side up, with about 1 inch of clearance between the top of the amps and the trunk subfloor.
To help with cooling, I've installed a vetilation system with 4 x 80 mm fans to circulate the air in the "amp chamber".
I've run this setup for a couple of months now and have spot checked after long periods of operation - the amp heatsinks are maybe 30 degrees when I touch them - very cool operation.
My JL dealer "certified" my installation, indicating they are confident that the installation orientation of the amps and fan cooling system are adequate for proper cooling. The things they looked for were the inch of free space above the amps, right side up amp orientation and adequate air movement in the chamber.
By using the board on top of the spare, the amps are mounted right side up, with about 1 inch of clearance between the top of the amps and the trunk subfloor.
To help with cooling, I've installed a vetilation system with 4 x 80 mm fans to circulate the air in the "amp chamber".
I've run this setup for a couple of months now and have spot checked after long periods of operation - the amp heatsinks are maybe 30 degrees when I touch them - very cool operation.
My JL dealer "certified" my installation, indicating they are confident that the installation orientation of the amps and fan cooling system are adequate for proper cooling. The things they looked for were the inch of free space above the amps, right side up amp orientation and adequate air movement in the chamber.
#12
Orientation won't matter aslong as you can get the heat off the heatsink (with airflow)
the airspace inside your amp shouldn't change do to orientation. it will be warm inside no matter what
in the spring I'll do some testing with some temp probes to determine if mounting the amp upside down has any effect on internal temps
the airspace inside your amp shouldn't change do to orientation. it will be warm inside no matter what
in the spring I'll do some testing with some temp probes to determine if mounting the amp upside down has any effect on internal temps
#13
Originally Posted by M-A3
... I've installed a vetilation system with 4 x 80 mm fans to circulate the air in the "amp chamber"...
#14
Air flow is key.
I currently have my amps mounted to the front of my speaker box (about an 80 degree angle) directly behind my rear seat. When my seats are in the up-right position, the amps only have 0.5" of air to breathe between them and the seat. In the summer time, after 20 minutes of playing loud, my sub amp gets hot enough to go into thermal protection (and the back of the rear seat is hot, and the heatsink is very hot). But, when the seats are folded down, the amps get enough airflow that they only get warm and do not go into protection. (Also, note that it is only my sub amp which goes into protection. The sub amp is running at the minimum 2 ohm load. My front stage which is 4 ohm stereo doesn't even get warm -that amp can handle 2 ohm stereo. So impedance is also a factor for the heat that will be produced)
So if you are going to mount them in any position other than flat, right-side-up, make sure that you have sufficient airflow.
I currently have my amps mounted to the front of my speaker box (about an 80 degree angle) directly behind my rear seat. When my seats are in the up-right position, the amps only have 0.5" of air to breathe between them and the seat. In the summer time, after 20 minutes of playing loud, my sub amp gets hot enough to go into thermal protection (and the back of the rear seat is hot, and the heatsink is very hot). But, when the seats are folded down, the amps get enough airflow that they only get warm and do not go into protection. (Also, note that it is only my sub amp which goes into protection. The sub amp is running at the minimum 2 ohm load. My front stage which is 4 ohm stereo doesn't even get warm -that amp can handle 2 ohm stereo. So impedance is also a factor for the heat that will be produced)
So if you are going to mount them in any position other than flat, right-side-up, make sure that you have sufficient airflow.
#15
It depends on the amp,I wouldnt do it it....but just keep in mind heat rises and if all the heat in your amp is stuck in a 1/4" gap between the circut board and bottom plate it will have overheating issues=clipping or cutting out.
Thread
Thread Starter
Forum
Replies
Last Post